IMPROVING MISTER SCREAMER; AN 80 DECIBEL FILAMENT ALARM

I created a prototype 3D printer filament alarm that worked, but the process also brought some new problems and issues to the surface that I hadn’t foreseen when I first started. Today I’m going to dive additionally into the prototyping process to get some insight on creating for a well-specified problem. What I came up with is an easy to build pendant that passively hangs from the filament and informs you if anything about that changes.

I began with a need to know when my 3D printer was out of filament, so that I could drop whatever I was doing and insert a new spool of filament ideal up against the end of the previous spool. By doing this within four minutes of the filament running out, printing very large jobs could continue uninterrupted. The device I created was called Mister Screamer.

The basic Concept

The idea is that if a 3D printer is attended (but not under constant supervision) and the operator is prepared to swap filament rolls when needed, then there is no need for the printer to do any “smart” tasks such as pausing the print. As long as there is a indicates of triggering an alarm when filament has run out, the operator can do everything needed to keep the maker printing uninterrupted, and the printer itself doesn’t even need to know.

First Prototype

The previous prototype used a roller switch to activate a buzzer. Filament was fed through the device.
The previous prototype physically sensed filament with a roller switch that triggered a buzzer when filament ran out. It had a successful trial run, but revealed some new problems:

When pulling filament through the device by hand there was little to no resistance felt, but once it was riding a roll of filament in the printer it created much a lot more binding and friction than expected. printing was successful but the printer’s extruder had to work much harder than usual. I had hoped the device would put a negligible strain on the feed system and filament. This was not the case.

When filament ran out, the device fell some distance to the tabletop. This was expected. But the impact nearly knocked the batteries completely loose from the friction-fit battery holder, which was not expected. had the batteries popped completely out, the device would not have done its primary job. The device needed to be drop-resistant, but the prototype design did not reflect this.

Even though the previous prototype did the job it was meant to do, it was clear there were problems and a design update was needed.

Design goals Summary

The fundamental requirements for Mister Screamer haven’t changed much. The device’s tasks are:

If filament is present, nothing happens.

If filament runs out, yell your deceive head off to alert a nearby operator.

Other elements of the design worked out well enough to keep, and remain mostly unchanged:

Enclosure can be 3D printed

Self-contained (no external power or signals)

Requires no modifications to the 3D printer to be monitored

Electrically simple, and using a minimum of easy to source parts

Long battery life, low power usage

Easy to turn off when responding to an alarm

Lessons from building and testing the first prototype were used to add the following design goals:

Must not interfere with the printer’s normal operation. Ideally, the printer must not even notice it.

Device need to be rugged and drop-resistant.

Ability to easily add the device to the filament of a print already in progress.

The New Prototype

The new prototype keeps the same basic function, but with an entirely different approach. The device is now sensitive to orientation, and senses the actual filament only indirectly. It is created to hang by a ball-link chain like a pendant.

While the device hangs down it is silent. If it falls, the alarm sounds until it is picked back up. Therefore in operation it hangs passively from the filament like a pendant or keychain as long as filament feeds into the printer. As soon as the spool of filament has emptied, the device falls to the tabletop and triggers the alarm.

The new system changes technologies. I did away with the roller switch and replaced it with a reed switch. inside the 3D printed enclosure is a void that captures a small disc magnet. The void has been engineered to use a shape that keeps the magnet away from the reed switch when hanging from the ball chain, but lay Mister Screamer on a flat surface and the magnet will clear up near enough the switch to actuate it.

rounded edges make sure it always lays flat after falling.

central M3 bolt secures both halves together.

Illustrated operation. Klicka för att förstora.

While hanging vertically from its chain (either for storage or when hanging from a filament line) the device is completely inert and uses no power. The enclosure is created with flat sides and rounded edges, so that the unit always settles to one side or the other when it falls.Central M3 bolt is plastic, so as not to interfere with the magnet.

Currently shrieking like a banshee in this orientation.

Other design Notes

Once the filament runs out, the device will fall to the tabletop.
There are a few other things to mention about the design:

The ball chain can be opened and closed. This indicates the device can be installed around filament while the printer is in use. No need to unload filament and thread it through the device like with the previous version.

The ball chain has another advantage: the smooth balls roll like little bearings on the filament itself. There is no perceptible wear or contamination risk.

Wiring all the parts — especially both battery contacts — into a single side of the enclosure indicated no flying wires between the two shells. This allowed me to glue wires in place, which in turn indicated much easier assembly (no pinched wires!) and a a lot more robust device overall.

There is a small amount of hysteresis from the attraction of the magnet to the ball link chain. The device requires a minor “tap” to shut off once it has turned on. This was pleasing but unintentional, and illustrates how closely physical design choices can affect operation.

Before creating the prototype I did a small proof-of-concept for a different idea: using a rolling ball tilt switch to sense orientation and activate the buzzer. These small devices use two metal balls inside a case to either close or open an electrical connection depending on orientation. regrettably the connection made is small, and they do not carry current very well. The buzzer emits only a faint, strangled sound with the power flowing directly through a rolling ball switch. This problem could be fixed by adding a lot more components to the design, but the rolling magnet and reed switch technique was chosen instead.

Video Tour

Warning: Audio consists of loud beeping

Resultat

The new prototype was a success, and not just because it done its intended job in the expected way. It was a successful process because:

It continued to validate the basic premise: the printer itself doesn’t need to know it’s out of filament, so long as an operator is notified and has time to act.

It was able to be created cheaply and quickly.

Design changes due to lessons learned from the original prototype were successfully integrated.

Using the Iterative Prototyping Process

In prototyping Mister Screamer, I did the following to get the best results from an iterative approach:

Define the problem and the scope carefully. Make sure that the problem you think you have is the same one that actually exists. In part one of this project, I figured out that my problem wasn’t really that my printer didn’t have a filament monitor. My problem was that filament could run out unnoticed even if I was in the same room.

Design something that solves the observed problem, no a lot more and no less.

Test certain ideas with a proof-of-concept before committing them to a prototype.

Make the prototype as swiftly and cheaply as you feasibly can.

Test in real-world conditions. The prototype will probably fail or fall short in at least one way, and hidden problems will be forced to the surface. Make sure failure results in something being learned.

Use what was learned to refine the design.

Mister Screamer V2 satisfied all the requirements, but still yielded discoveries that could be used to improve a subsequent version. The greatest lesson learned was that this design is highly dependent on the layout of the 3D printer being used.

In my particular printer (a Raise3D N2) the filament spool is well away from the print area. Not only is there room for the device to hang from a spool, there isn’t any risk of the unit ending up somewhere troublesome when it falls. other 3D printers may have physical layouts that don’t allow Mister Screamer to work well. If the device dangles in the way of the print head, or can fall into the print area once filament runs out, that’s asking for trouble.

As it stands, Mister Screamer V2 does its job well enough to be reliably used for real work, even if its scope is focused generally on my own printer and needs. Ever-increasing improvements can be tempting to chase, but it’s rarely needed to iterate until a option is perfect. If a problem has been correctly identified and understood, it becomes much much easier to judge when the option is done.

The enclosure design for this version of Mister Screamer is available on GitHub.